Cisco 300-420 ENSLD Training Questions have been Updated
By Examgood | March 11,2021 07:44 AM
Designing Cisco Enterprise Networks (ENSLD) 300-420 training questions have been updated, which will be your best guides to prepare the test. The Designing Cisco Enterprise Networks v1.0 ENSLD 300-420 exam is a 90-minute exam associated with the CCNP Enterprise and Cisco Certified Specialist-Enterprise Design certifications. To prepare this Cisco certification 300-420 ENSLD exam, the new Cisco CCNP enterprise 300-420 ENSLD training questions are helpful in the preparation.
300-420 ENSLD Designing Cisco Enterprise Networks Exam
Cisco certification 300-420 ENSLD exam certifies your knowledge of enterprise design including advanced addressing and routing solutions, advanced enterprise campus networks, WAN, security services, network services, and SDA. You can register this Designing Cisco Enterprise Networks 300-420 ENSLD exam at Pearson VUE test center. The 300-420 ENSLD exam language is English.
Cisco 300-420 ENSLD Exam Topics
Check Cisco certification 300-420 ENSLD exam topics in the following picture.
Study Latest Cisco 300-420 ENSLD Exam Training Questions
Study the latest Cisco 300-420 ENSLD exam training questions to prepare this test. Share some Designing Cisco Enterprise Networks 300-420 ENSLD exam training questions below.
1.A company is running BGP on a single router, which has two connections to the same ISP. Which BGP feature ensures traffic is load balanced across the two links to the ISP?
A. Multihop
B. Multipath Load Sharing
C. Next-Hop Address Tracking
D. AS-Path Prepending
Answer: B
2.Which design consideration should be observed when EIGRP is configured on Data Center switches?
A. Perform manual summarization on all Layer 3 interfaces to minimize the size of the routing table.
B. Prevent unnecessary EIGRP neighborships from forming across switch virtual interfaces.
C. Lower EIGRP hello and hold timers to their minimum settings to ensure rapid route reconvergence.
D. Configure multiple EIGRP autonomous systems to segment Data Center services and applications.
Answer: A
3.Which design consideration must be made when using IPv6 overlay tunnels?
A. Overlay tunnels that connect isolated IPv6 networks can be considered a final IPv6 network architecture.
B. Overlay tunnels should only be considered as a transition technique toward a permanent solution.
C. Overlay tunnels can be configured only between border devices and require only the IPv6 protocol stack.
D. Overlay tunneling encapsulates IPv4 packets in IPv6 packets for delivery across an IPv6 infrastructure.
Answer: C
4.When a network is designed using IS-IS protocol, which two circuit types are supported? (Choose two.)
A. nonbroadcast multiaccess
B. multiaccess
C. point-to-multipoint
D. nonbroadcast
E. point-to-point
Answer: BE
5.What is an advantage of designing an out-of-band network management solution?
A. In the event of a production network outage, network devices can still be managed.
B. There is no separation between the production network and the management network.
C. In the event of a production network outage, it can be used as a backup network path.
D. It is less expensive than an in-band management solution
Answer: A
- Related News
- What should we do with 700-751 dump as we approach the exam? January 02,2020
- CCNP Security: Cisco Certified Network Professional Security December 31,2019
- How to learn SMB track 700-751 well? December 19,2019
- 300-175: Implementing Cisco Data Center Unified Computing (D... December 16,2019
- 400-251: CCIE Security Written Exam (v5.0) exam December 12,2019
- 400-101: CCIE Routing and Switching Written Exam December 02,2019
- 300-320: Designing Cisco Network Service Architectures November 21,2019
- CCNA Data Center certification exam November 11,2019
- CCNP Routing and Switching Certification October 24,2019
- Best CCNA R&S (200-125) Certification Exam Dumps October 14,2019